Brand New Custom PC Won't turn on

JingKoB

New Member
I checked the Jumpers for the PWR SW and etc and they seem to be in right. The jumper cables dont have plus and minus on them so idk how to determine which way they go in.

Specs Are:
Intel Q8400 2.66GHz
Gigabyte EP43-UD3L
Western Digital Green Power 640GB HDD
EVGA nVidia GeForce 9600GT PCI-E 2.0 512MB Graphics Card
2x Corsair XMS2 2GB RAM (Total of 4GB RAM
topower 650W Power Supply

I have only installed one stick of RAM first, and will install the 2nd later, once it works.

Any ideas on why it wouldnt turn on?

Thanks!!
 
Try the other stick of ram instead of that one.

Maybe your powersupply is not good.

Check all your connections again.
 
You want to double check the jumpers; try them the other way.

Yeah I'd try to see if it's defective RAM or not..

Did you plug in the 4-pin CPU power connector the RIGHT way? There's only one RIGHT way that you can put it in. Look at the designs on the connector to see if you have it in correctly so that it matches the plug on the motherboard...
 
we switched the ram and it still didnt work. it seemed that a light near the ram flashed. and also the light on the dvd drive flashed.

we dont have SYSFAN1 or PWRFAN plugged in cuz the power supply doesnt have any 3-pin connectors. is that bad?

we do have SYSFAN2 in though.

and the cpu fan is in right.
 
we switched the ram and it still didnt work. it seemed that a light near the ram flashed. and also the light on the dvd drive flashed.

we dont have SYSFAN1 or PWRFAN plugged in cuz the power supply doesnt have any 3-pin connectors. is that bad?

we do have SYSFAN2 in though.

and the cpu fan is in right.

Wait. PWRFAN meaning, power supply fan?
If so, that's why it's not turning on...
 
does it respond at all when you press the power button?

when we switch the pwrsupply on we can see and hear the fans inside the power supply running. when we hit the power button the ram light and the dvd drive light flashes. thats it though.
 
i found this article online about the PWR_FAN

The 3 pin pwr_fan connectors on your mobo supply power TO your fans. They use 2 of the pins for that. The third pin is to monitor fan speed. Antec power supplies often have a connector with 3 pins but only one wire to supply the mobo with PSU fan speed info. NO power should ever be INPUT to the pwr_fan connectors. Run your system fans either from the power supply using 4 pin molex connectors or the pwr_fan 3 pin connectors on the mobo. Make sure that the CPU heatsink/fan 3 pin connector is plugged into the mobo and you should be good to go. You should not find a 3 pin 3 wire female fan connector in the power supply wiring bundle. The Asus manual must have a misprint.

and it is not an Antec Power Supply.

if we just plug the power switch jumper in and not the others. it should still turn on right?
cuz the others are just LED lights.
 
Ok.. Take out your graphics card and plug your monitor in to the Onboard connection... See if it turns on?

1. there is no onboard graphics card on the mobo. the only monitor port is on the graphics card.

2. we havent plugged in a monitor just yet. we want it to turn on first =/. that shouldnt be a problem right?
 
What kind of mother board does have an onboard graphics? It doesn't have a VGA/DVI port?

not having a monitor won't be a problem, you should still take out the graphics card and try starting it up.
 
I checked the Jumpers for the PWR SW and etc and they seem to be in right. The jumper cables dont have plus and minus on them so idk how to determine which way they go in.


I have only installed one stick of RAM first, and will install the 2nd later, once it works.

Any ideas on why it wouldnt turn on?

Thanks!!

when we switch the pwrsupply on we can see and hear the fans inside the power supply running. when we hit the power button the ram light and the dvd drive light flashes. thats it though.

Are you sure the 4/8 pin CPU power connector is plugged in. Plus did you put the standoffs under the board in all the right places, not one where it doesnt belong.

What kind of mother board does have an onboard graphics? It doesn't have a VGA/DVI port?

Alot of boards dont have onboard video, mine doesnt. Untill the last few years only lowend budget boards came with onboard. Really still most higher end board dont.
 
What kind of mother board does have an onboard graphics? It doesn't have a VGA/DVI port?

not having a monitor won't be a problem, you should still take out the graphics card and try starting it up.

we tried that and it still didnt turn on. but mostly only OEM mobos have onboard grphx cards.
 
Ok so if it isn't the standoffs, graphics card, PSU (you did try a different PSU, right? just because the fans turn on doesn't mean it's fully functional.) and RAM. Did you properly install the processor, and you did plug in your CPU heatsink fan? Did you try putting in a different hard drive?
 
Are you sure the 4/8 pin CPU power connector is plugged in. Plus did you put the standoffs under the board in all the right places, not one where it doesnt belong.



Alot of boards dont have onboard video, mine doesnt. Untill the last few years only lowend budget boards came with onboard. Really still most higher end board dont.

yes i am sure the 4/8 connector is in all the way and correctly. and all the standoffs are in.
 
If you have one where it doesnt belong it can ground out against the bottom of the board and keep it from firing up. They only go where there is a grounding strip around the hole in the motherboard.

yeah they are only where the ground strips are. there is one ground hole where there is no hole in the case, so i didnt put any thing there.
 
I'm going to re-post my post because it was overlooked:

Ok so if it isn't the standoffs, graphics card, PSU (you did try a different PSU, right? just because the fans turn on doesn't mean it's fully functional.) and RAM. Did you properly install the processor, and you did plug in your CPU heatsink fan? Did you try putting in a different hard drive?
 
if pressing the power button on the front of the case does nothing your wires are crossed on the mobo.

If it turns on but nothing shows on the screen then you have a loose connection o nthe 4/8 pin which i ran into a week ago.

Start from scratch. Unplug all wires and redo them. take your time on the case wires and be sure the case speaker is wired up to hear any beeps.
 
Back
Top