I Need An Expert

jimkiker

jimkiker

New Member
I NEED YOUR HELP!!!!
GUYS,to start with... I own a i845wn Mobo,a socket 478 fsb 400 1.7 ghz intel p4 proc.,an ati 9200se 128 mb graphics card and stuff like this ..
One day i realised that my system was crap,so i wanted to buy a new mobo supports agp8 and ddr 400 ram memory and of course my proc. So, i bought
9PJL Apogee Chaintech mobo (http://www.chaintechusa.com/tw/eng/product_spec.asp?MPSNo=13&PISNo=159).I Bought a used one cause i wasnt able to find a new one.The person sold it to me was a known and the mobo was workin perfect 100% When i set it up the pc was able to start ( i mean that the processor fan started workin but i couldnt hear the "Beep" from the mobo speaker.I realised that the monitor was not startin.i checked the connections and everything was perfect..Just the monitor was not startin.. I went to my neighboorhoods pc shop and they checked that..The said that mobo was not workin and it was Dead..I sold it back to the guy and he set it up to a pc he had and it just .. WORKED... He gave me another mobo then the: Chaintech 9CJS (http://www.chaintechusa.com/tw/eng/product_spec.asp?MPSNo=13&PISNo=144) I set it up and just the same...Any ideas??
1) The mobos work thats sure..
2) My " set up " work is probably good cause they checked it from the pc shop..
3) I dont wanna give back again this mobo.. PLZ HELP.. I need an expert..The monitor stays off ... and the speaker does no voice..Just the proccesor fan starts..

Jimmy
 
You sure you connected everything? Oh and if there are those fancy diagnostic leds you should check out how they're lit, they usually have about 1-2 pages about those in the manual. For example, on my mobo I have 4 leds. If they are all red the CPU is busted or not correctly installed, 3 red and 1 green means in my case that there is a problem with the memory etc.
 
Follow what mrjack said, and also try booting without your ram installed, and any other devices that are not critical. It could be a problem wiht the psu or video card.
 
id it actually do anything? you should check on the internet on the compartibility list of the mobo, if that mobo does support you CPU.
i mean.. my old K7T-Turbo Limited Edition board could support only till the AMD palomino core.. the other CPU (barton and those cores) wernt supported, so the mobo acted as if there was no CPU insterted at all.. ;)

If you cant find that list/table, try fireing op your system without CPU in the socket.
my quess is , that it still does the same (Fans start running, but monitor stays black
 
You don't say what PSU you have. You are going from a low power system to a higher power system and the psu may not be up to the task. Your cpu should be fine with the new board and the memory as well.
Try a barebones boot with only the mobo, cpu, memory, psu, hdd and vid crd.
Reset you cmos using the jumper to clear. check to see if the cmos jumper is in the correct position as the clear position will give the same results as you descibe.
 
Follow what mrjack said, and also try booting without your ram installed, and any other devices that are not critical.
Click to expand...
I hope yer not suggesting RAM isnt critical to the boot process

Follow what mrjack said, and also try booting without your ram installed, and any other devices that are not critical.
Click to expand...
Yep, the fans are kicked in by power

Try a barebones boot with only the mobo, cpu, memory, psu, hdd and vid crd.
Click to expand...
HDD isnt a core boot requiement :)
 
Well the no video could be your
A:Bad video card/ not pushed in all the way
B:Bad Ram/not pushed in all the way
C:Weak PSU(PLZ tell us the specs on the PSU(PSU= Powersupply unit))

I would check these first. If you don't have enought power video is one of the first to go. If you have no ram or it's not in all the way you'll have no video and if you video card is dead you'll have no video.
 
You must log in or register to reply here.
Back
Top