Upgrading CPU, Need Help

[Riaorak919]

Nil

Nil

 

[johnb35]

We can't give you answer until we know what motherboard was used if this is a custom built machine or what model of pc if this is a store bought pc. Once we know this information we can help you as not all motherboards support the same cpu's.

 

[StrangleHold]

Any AM3 processor 95W and under.
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c02458055&cc=us&dlc=en&lc=en&product=4216558

 

[StrangleHold]

Ok what about this one?

http://www.newegg.com/Product/Product.aspx?Item=N82E16819103962

It's AM3+ 95W... But I dunno what that + means. So not sure if this will work for me. Preferably looking for a six core processor.

Nope, doesnt support AM3+

 

[Mia]

Here's one that's AM3 and still six cores =)

http://www.newegg.com/Product/Product.aspx?Item=N82E16819103856

Mia
<3

 

[StrangleHold]

Since its clocked low and a 95W model. You could use the same heatsink and fan on your Athlon II X2. As long as your not overclocking, which I doubt on a OEM board. Just clean off the old CPU compound and apply new. Or you could go with a Athlon II X4.

 

[Mia]

Yeah =D

StrangleHold is right, besides, there are only two other CPU's that are AM3, Six Cores and Include a fan. Both of these, however, are 125w instead of 95w =(

 

[KingEojj]

grab this 2gb 550ti instead of that 1gb 6770...

http://www.newegg.com/Product/Product.aspx?Item=N82E16814130652

 

[Mia]

Since you're getting it from Newegg this one seems appropriate =)

http://www.newegg.com/Product/Product.aspx?Item=N82E16835186038

You actually put the thermal paste on the top of the CPU, putting it on the bottom of the fan can easily result in using too much

Just squirt some onto the CPU then spread it over so it covers the entire surface.. It's safe to use your fingers to spread it but meh.. Matter of preference :3

 

[Troncoso]

The best way to make sure you get enough thermal paste, without getting too much, is to simply apply a pea size drop in the center of your CPU (once it is installed). From there, simply place your heat sink on top of it and secure it in place.

 

[Troncoso]

Question. If I applied too much what happens? Just curious.

So just apply a small pea dot size in the center, spread all around and place the heatsink/cooler back on?

The reason you don't want to much is just because when you place the heatsink on it, it'll run over and get on your processor/motherboard. It's not a good thing.

Also, Don't spread it around. Once you apply the drop, simply place the heatsink on top of it. That'll give you the most even coating.

 

[StrangleHold]

Put a rice size amount in the middle of the CPU and let the heatsink spread it out. Or you can use the same amount and spread it out as even as you can. With a stock heatsink its not going to matter either way. Just make sure you get the old stuff cleaned off the bottom of the heatsink good.

 

[StrangleHold]

Open it back up and make sure you didnt bump anything loose. You still should replace the compound taking one off like that.

 

[StrangleHold]

Did you boot it up before this to make sure it was still running? Try reseting the bios, with the jumper on the board or take the battery out for a few minutes. Do this with it off and unplugged.

 

[johnb35]

Looks like video card is bad. Does it have onboard or dedicated card?

 

[SMGOwnage]

It probably is POST-ing you just cant see it becuae of faulty graphics card