Unique prob with the build
ok,
It's been a while, and this is what I bought with the trouble I am having.
I hope someone has run into this seemingly unique prob and able to overcome it. I am trying to avoid taking it to a shop!
This maybe a little long(?), but I wanted to give you all the info I have.
I am wanting to reuse my HD's which are PATA ( IDE)
Here is what I have.....
MOTHER BOARD: ECS BLACK SERIES A790GXM-AD3 AM3 http://www.newegg.com/Product/Produ...C-Bleeping&cm_mmc=AFC-Bleeping-_-NA-_-NA-_-NA
Brand ECS
Model A790GXM-AD3
Supported CPU CPU Socket Type AM3 CPU Type Phenom II
Physical Spec Form Factor ATX
Power Pin 24 Pin
(Note: This board supports CPU up to 140W TDP only)
FSB 2600MHz Hyper Transport (5200 MT/s)
Chipsets
North Bridge AMD 790GX -South Bridge AMD SB750
Memory
Number of Memory Slots 4×240pin
Memory Standard DDR3 1333
Maximum Memory Supported 32GB (8GB tested)
Channel Supported Dual Channel
SATA RAID 0/1/5/10
Onboard Video
Onboard Video Chipset ATI Radeon HD 3300
CPU: AMD Phenom II X3 720 2.8GHz http://www.newegg.com/Product/Produ...C-Bleeping&cm_mmc=AFC-Bleeping-_-NA-_-NA-_-NA
AMD Phenom II X3 720
Model HDZ720WFGIBOX
CPU Socket Type Socket AM3
Tech Spec
Multi-Core Triple-Core
Operating Frequency 2.8GHz
Hyper Transports 4000MHz
L1 Cache 128KB+128KB
L2 Cache 3 x 512KB
L3 Cache 6MB
Manufacturing Tech 45 nm SOI
64 bit Support Yes
Thermal Design Power 95W
RAM G.SKILL 4GB (2 x 2GB) 240-Pin DDR3 SDRAM DDR3 1333 –
http://www.newegg.com/Product/Produ...C-Bleeping&cm_mmc=AFC-Bleeping-_-NA-_-NA-_-NA
power supply:OCZ StealthXStream OCZ600SXS 600W http://www.newegg.com/Product/Produ...C-Bleeping&cm_mmc=AFC-Bleeping-_-NA-_-NA-_-NA
CASE: COOLER MASTER Centurion 5 CAC-T05-UW
http://www.newegg.com/Product/Produ...C-Bleeping&cm_mmc=AFC-Bleeping-_-NA-_-NA-_-NA
THE PROBLEM
( Note board only has 1 IDE plug)
I put everything together: MB light and case and cpu fan goes on.
HD ( IDE) and CD/DVD configured to Master and Slave. Neither would turn on if the IDE cable is plugged in!

Tried 3 diff cables with appropriate ends for master & slave ( I do not have SATA anything). Still no signal from MB to monitor - monitor stays blank like nothing is connected to it. Tried 3 monitors
Completely removed HD, CD/DVD – still no signal to monitor!!

(From what I understand, just to see bios, I do not need the HD. - I just want to see signal to computer!)
Bare minimum to see bios is MB, RAM (?), PS, CPU, monitor.
Did the below with no positive results
Replaced MB with same MB
- with identical results, no signal; on monitor, HD - CD/DVD will not run with IDE cable .( I do not have a SATA HD)
Replaced RAM
Exchanged PS from other computers here.
( Just to make sure is ok to do, unplugged PS connector to MB from extra running computer, and plugged it into MB of troublesome MB)
Did not replace CPU, was trying to avoid that. Do not have one lying around, am very hesitant to remove processors from other home computers.
Guessing I will have to take this to a local fix shop just to plug in a CPU to confirm the MB is again not bad - or CPU is bad. fix shop is ~ $80/hr.
I want to avoid that hoping someone here can help
Anyone have this prob?
I read the cons on newegg site for the MB, few had trouble, but some said the MB “would not post”: - what does that mean?
Also some said they had to reset the MB, I have to look into how to do that ( with power on/off?).
Contacted the MB company, they said to replace everything, which I did but the CPU
Hope you can give some insight!!!!
Thanks!!!!!!!!!!!!!
Matt