OC'ing E6300

I didn't see any performance gain when @ 2.4Ghz compared to the 1.86Ghz at stock.

About my Northbridge, is it being warm (not burning my hand) Ok? Is there a way I can check the temps of it?
 
Kornowski said:
I didn't see any performance gain when @ 2.4Ghz compared to the 1.86Ghz at stock.

About my Northbridge, is it being warm (not burning my hand) Ok? Is there a way I can check the temps of it?
Click to expand...

Warm = fine. Unbearably hot = bad. Slowly start taking it up to 2.8 GHz now. You won't regret it.
 
Ok, It's hot / warm, it doesn't burn me so I guess that's Ok.

How much hotter will it get if I add 0.1v to the MCH?

Is that all I should do, then put the FSB up some more?

Thanks :)
 
Kornowski said:
Ok, It's hot / warm, it doesn't burn me so I guess that's Ok.

How much hotter will it get if I add 0.1v to the MCH?

Is that all I should do, then put the FSB up some more?

Thanks :)
Click to expand...

Yeah, sounds right. What is the default voltage your RAM takes?
 
Ahh, ok, same RAM. That means that by default (without overclocking) you should be running your RAM overvoltage setting at +0.1v, since our RAM requires 1.9v (instead of the BIOS's default 1.8v).

So make sure you add that extra 0.1 volt to the MCH and RAM. ;)
 
Kornowski said:
Ok Sure, Thanks a lot Rambo!

Howcome you've dropped yours from 3Ghz to 2.8Ghz?
Click to expand...

Well, I know it's not much of a difference from 2.8 to 3.0 (that's 57 MHz extra on the RAM) but I just felt it was stabler at 2.8 GHz. I may take it up again actually, to see how it goes. But as of now, it's REALLY stable - hasn't crashed in months!

:)
 
Ah right, Yeah, It's better to have it stable than running slightly faster... Mine hasn't crashed since I got it, Don't know how long it's been, but I haven't had it OC'ed.
 
Kornowski said:
Ah right, Yeah, It's better to have it stable than running slightly faster... Mine hasn't crashed since I got it, Don't know how long it's been, but I haven't had it OC'ed.
Click to expand...

Well, there will be a time when it resets itself cause it's overclocked too much - and then you know it's time to up the voltage, or just go back down. :)
 
So I could test it with Orthos you mean, and if it passes stable, it could still restart some other time?

I may just shoot for 2.4Ghz or 2.6Ghz, I don't think I'd need / want to go any higher... I think I need to buy a new HSF before I try it again, because I was idleing at about 38c.

Howcome my RAM is working fine when it's 0.1v under the recomended?
 
Kornowski said:
So I could test it with Orthos you mean, and if it passes stable, it could still restart some other time?

I may just shoot for 2.4Ghz or 2.6Ghz, I don't think I'd need / want to go any higher... I think I need to buy a new HSF before I try it again, because I was idleing at about 38c.

Howcome my RAM is working fine when it's 0.1v under the recomended?
Click to expand...

No, I meant as you overclock it, you may find it'll restart/crash and that's when you know to up the voltage or take the FSB down.

And your RAM works at 1.8v, but the recommended is 1.9v. It's up to you what you want to run it at, but if you want to overclock your RAM, it's best to put it on +0.1v at least.
 
You must log in or register to reply here.
Back
Top